Skip to content
Altomer Polyplast — Masterbatch | Additives | Compounds
Quality control laboratory testing

Quality Control & Laboratory

Batch-to-Batch Repeatability. Calibrated for Zero Conversion Downtime.

Uncompromised dispersion is not an aspiration, it is a measured specification. Our dedicated testing facility screens every production lot against ASTM and ISO parameters for melt viscosity, active pigment loading, and sub-micron dispersion before issuing dispatch clearance.

Core Tests

Three measurements that predict your line.

  • MFI testing

    ASTM D1238 / ISO 1133

    Melt flow index at 190°C under 2.16 kg (and 21.6 kg for pipe grades) confirms the masterbatch will let down cleanly into your resin.

  • Dispersion analysis

    EN 13900-5 · ISO 18553 · DIN 53770

    Filter pressure value at 14 μm, microtome dispersion rating and 45 μm mesh retention reveal agglomerates before they reach your screen pack.

  • Spectrophotometry

    Delta-E · CIE whiteness

    Instrumental color measurement approves shades to Delta-E < 0.5 and verifies whiteness index on filler compounds.

Test Methods

The standards behind our TDS values.

Typical properties on our technical data sheets are reported against these international methods.

PropertyMethod
Active pigment / filler contentMB-W70-PE, CP-CA80-PEASTM D5630 / ISO 3451-1
Carbon black contentMB-BLK40-AGASTM D1603 / ISO 6964
Specific gravity (density @ 23°C)All standard gradesASTM D792 / ISO 1183
Melt flow indexAll standard gradesASTM D1238 / ISO 1133
Moisture / volatilesAll standard gradesASTM D6980
Filter pressure value (14 μm)MB-W70-PE, MB-BLK40-AGEN 13900-5
Dispersion rating (microtome)MB-BLK40-AGISO 18553
Mesh retention (45 μm)CP-CA80-PEDIN 53770
Thermal heat stabilityAll standard gradesDIN 53772
Light fastnessMB-W70-PE, color masterbatchesISO 105-B02 (Blue Wool)
Kinetic coefficient of frictionMB-ADD-SABASTM D1894
Haze / optical clarityMB-ADD-SABASTM D1003
Primary particle sizeMB-BLK40-AG, MB-ADD-SAB, CP-CA80-PEASTM D3849 (TEM) · laser diffraction
Bulk densityMB-W70-PEASTM D1895

Shade Matching

The 48-hour lab loop.

Color matches follow the same documented four steps every time.

Color matching swatches
  1. 01

    Target Sample Submission

    Share Pantone code, RAL, reference part or physical sample, along with your base polymer and production process.

  2. 02

    Carrier & MFI Calibration

    We select & recommend the carrier and tune melt flow so the masterbatch lets down cleanly into your resin.

  3. 03

    Plaque Extrusion & Shade Match

    Lab plaques are extruded and checked by spectrophotometer to Delta-E < 0.5.

  4. 04

    Trial Lot Dispatch

    Prompt shipment of trial lots post plaque approval for your production line trial – All Within 48 Hours!

FAQ

Lab tests, answered.

  • What is a filter pressure value (FPV) test?

    A dispersion test. The filter pressure value test method, EN 13900-5, pushes melt through a fine 14 μm screen and reports the pressure rise in bar/g. Lower values mean better dispersion, fewer screen changes and fewer specks in film. MB-W70-PE is specified at FPV < 0.8 bar/g and MB-BLK40-AG at FPV < 1.0 bar/g.

  • How is masterbatch MFI tested?

    Melt flow index is measured to ASTM D1238 / ISO 1133 at 190°C under 2.16 kg, and under 21.6 kg for pipe grades, to confirm the masterbatch will let down cleanly into your resin.

  • How is carbon black dispersion rated?

    With the ISO 18553 dispersion test, a microtome rating of undispersed agglomerates; MB-BLK40-AG is rated ≤ 2. Carbon black content is checked to ASTM D1603 / ISO 6964.

Free Sample

Have a line trial coming up? Let's match the grade to it.

Send your polymer, process and target let-down. Our lab confirms, tests and formulates the grade and dispatches a sample.